Just about every person may have his or her own piece of advice involving How to Install a Bathtub.
Setting up a bath tub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily available, the project can relocate easily; if you need to open a wall to get rid of the old tub and place the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is far better to think about using one before you start. Possibilities are you may require an expert plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your washroom if you have currently gotten a new bathtub and don't require to alter the setup of your previous water system pipes.
Your devices and product checklist must comprise the following:
Getting ready for the Installation
First of all, the supporting framework provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also changing the feet on the bathtub till the spirit level reviews degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and tighten them if essential. Load the bathtub and additionally examine the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has actually been used at least once as this will certainly resolve it right into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, creating the water to permeate the wall between the bath and the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and also installations. They are offered in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can split relatively early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that blog posting on Installing A Bathtub when surfing the search engines. Do you know about anybody else who is involved in the subject? Be sure promote it. We value reading our article about Installing A Bathtub.
Or Book Technician Here